7/2/2023 0 Comments Dead air keymo muzzle brake![]() Department of State, Office of Defense Trade Controls, prescribed in the International Traffic in Arms Regulation (ITAR), Title 22, Code of Federal Regulations, Parts 120-130. This product is manufactured in the USA by LANTAC USA LLC for sale within the USA only.Įxport of the commodities described herein is strictly prohibited without a valid export license issued by the U.S. If you would like to add shipping insurance to your order, please purchase here. MIL/LE discount available, please visit our FAQ page on how to obtain the discount code. Lantac recommends the use of semi-permanent thread locker Rocksett, sold separately.ĭimensions: L: 2.760', DIA Body: 0.824'' MOUNT: 1.080’’. The mount design is fully licensed from Dead Air, therefore customers suppressor warranty remains unaffected. Exteriors surfaces are Cerakote® finished for ultimate durability.ĭragon brakes are precision manufactured on Swiss lathes and machined from AISI4140 steel that is then hardened to 48-52Rc (Rockwell C) and QPQ (Quench Polish Quench) Nitrided to AMS2753D standards for enhanced corrosion resistance and improved lifespan. The Sandman range of silencers are manufactured with solid welded Stellite® baffle cores and detachable front caps. Its unique Short Energy Pulse system reduces length of recoil so that repeating shot energy cannot overlap and knock the shooter off target.įull auto fire is possible with massively reduced recoil and muzzle climb, meaning that all shots fall on target.įor the first time shooters can now enjoy advanced weapon control with the ability to mount the entire range of Dead Air® Sandman® KEYMO ™ silencers to their firearms. Manufactured to the highest quality standards and featuring a patented design, the LANTAC DGN556B-DA™ Muzzle Brake offers improved recoil management and muzzle rise over competitors products. Oddly enough, I have one 1/2"-28 muzzle brake with and one without wrench flats, so I'm stumped.Estimated Ship Date From Time of Order: 3 - 4 weeks For this style, you would definitely want the shoulder or shims to be slightly in front of the end of the you please confirm which version of muzzle brake is the current design with rear wrench flats or without? Thanks!ĥ/8 x 24 muzzle brake does not have the pin & weld stand-off IN STOCK LANTAC Dragon Muzzle Brake DGN762B-DA for AR10, 308-style, & 300 Blackout Rifles.Manufactured to the highest quality standards and featuring a patented design, the LANTAC DGN762B-DA Muzzle Brake offers improved recoil management and muzzle rise over competitors products.Its unique Short Energy Pulse system reduces length of recoil so that repeating shot energy cannot. ![]() However, the rest of my muzzle brakes do not have wrench flats at the rear, which makes the rear of the suppressor sit almost dead even with the rear of the mount. ![]() I also have one 1/2"-28 muzzle brake with wrench flats at the rear, which would measure the same. The above measurements are for the Dead Air Keymount flash hider, which has the wrench flats at the rear of the mount. I don't have an actual Key-Mo adapter to measure, but if it's the same as the integral mount on the Sandman suppressors, the rear edge of the adapter should sit about 1/8" to 3/16" in front of the shoulder when mounted.Īs long as your shoulder is even with or very close to the end of your handguard, you should be fine. To me, it looks like the Keymo mount comes much farther back on the muzzle device than most, almost covering the wrench flats at the back.Ĭan anyone provide the distance measurement from rearmost point on the muzzle device, to the rearmost point of the mount when mounted? I know the Surefire open tine flash hider will push thier mount far enough out with just a “medium” sized shim, but that doesnt provide much reference unless i posess both mounts/muzzle devices. None of my local dealers have a mount I could “try on”. My question, finally, is how would I go about measuring for clearence between mount and forwad edge of the rail? I will obviously have to use a shim or two, but want to avoid having to use a whole damn shim pack to get the mount away from the rail. Obviously there isnt much room from front of the rail to front of the barrel. ![]() Barrel on the host will be 14” and the rail is one of the 13.5” MK16s from black friday. Looking to grab my first supressor, yay me!Īfter much research, I would really prefer to go with the Dead Air Keymo mount, most likely with a Vox K. ![]()
0 Comments
Leave a Reply. |